This project has as main goal to study the influence of the coating thickness, deposited by arc-PVD- technology, on the wear resistance of coated cemented carbide inserts in three different turning operations. An additional effort has also been made to develop a new test method for evaluating flank wear resistance. Three different coating types (Coating A, Coating B and Coating C) have been studied in three distinctive thicknesses (2, 4 and 6 µm) for each type. For two of the coating types (Coating A and B) special studies has been done with the thickest coating, creating two additional coating versions of the thickest coating, by changing various deposition parameters, with the aim to enhance the cohesive properties of the coating and lower the residual stresses at the cutting edge. The results show increased crater wear resistance with increased coating thickness for all coating types, but the amount of increase changes with coating type (Coating A>B>C).

The thesis evaluates a new kind of bearing arrangement in a traction motor that ABB hasdeveloped. Since the arrangement is designed in a new and innovative way it needs to beevaluated to see if it is safe to use. In today?s traction motors, bearings with a big internalclearance (C4-clearance) are used. The basic idea of the new arrangement is to reduce the fitsbetween the bearing and shaft/house.

Floor surface in pig facilities can have an impact on animal welfare and pig health, as it can cause the pig physical damage and thereby increased risk of infectious diseases and lameness. The development of pig housing systems has resulted in a decreased use of bedding. It seems hard to find the optimal floor in farrowing pens, as it must suit both the sow and piglets. The floor friction needs to be adequate to avoid slips and at the same time should the floor be non-abrasive. Abrasions and lesions caused by the floor are not only causing the animal suffering, but are also negative from an economical aspect.

Title in original language: En undersökning av tre olika behandlingsmedels effekt påvegetabiliskt garvat läder för bokbandLanguage of text: SwedishNumber of pages: 32.

The development of defoaming additives is steadily progressing and there are therefore always new and improved additives on the market. Some modern additives provide the desired defoaming effects by themselves, in contrasts to previous additives that needed to be used in combination with other additives. The task of this bachelors thesis was to evaluate the possibility of using these improved defoaming additives, with the aim to find alternatives that give the system better defoaming attributes while, at the same time, using less of the primary products. The tests were carried out in the coating type Teknocryl Aqua Combi 2780. The coating is a waterborne air drying acrylat-latex/alkyd based coating that can be used for both single coat painting and primer.

Steel is an excellent material to build with, but consideration must be given to the fact that unprotected steel corrodes, rusts, therefore, as a rule, the steel must be protected in some way. This can be done by reducing the tendency of the steel to corrode by using stainless steel or by treating the steel with a protection method. The two most common methods of protection are corrosion protection paint and zinc coating. To determine the method, the corrosive category must first be evaluated and this is done in accordance to EN ISO 12944-2:1998.Stainless steel is available in many varieties but only some of them have properties that make them suitable for use as construction steels. There are many factors to be considered in the design of stainless steel to prevent corrosion from occurring.

ABSTRACTMany wind turbines have problems with icing and there is still no effective method to de-ice without stoppage of production and power loss. Here I therefore consider other methods than those available today, and particularly, I consider how these methods could be applied to wind turbines of the company Oxel. A surface where the water droplets do not attach might be the basis for a useful method. If no water attaches, no ice could form. To accomplish this a hydrophobic surface is nessesary, for example wax.

Atlas Copco Tools develops and manufactures handheld industrial tools. Heat and surface treatments are used to provide the tools with certain properties. There are no routines for the choice of treatment or for how to specify treatment on drawings. Production documents that are sent for production abroad may not be clear enough. Some treatments are known as trademarks and there are no instructions for how to specify these on drawings and in CAD-models.The purpose of this master thesis work is to create recommendations for the procedure of choosing heat and surface treatment.

By our employer Camatec Industriteknik AB have we been given the assignment to continue with the previous work ?Design of strip feeder?. Our goal with this work is to come up with a design basis for a strip feeder.Functionally a strip feeder consists of two rollers which with the aid of the friction between the strip and the coating on the roller create a strip force that pulls the strip through the working progress.Demands on this project:? 10 ? 600 mm in strip width and 0,1-1 mm in strip thickness.? Minimum 30m/min in production speed.? A maximum strip force on 30-40 kN.? The cost of the strip feeder?s components is to be considered of economy and quality.The need of a strip feeder occurs when the coil doesn?t manage to feed or pull the strip before or after a working process. The strip can otherwise be exposed by a permanent yield deformation or a change in the strip material if it?s pulled trough the working process only by the on ? and of-coils.

In my thesis I have sand blasted different type of woods - ring-porous and diffuseporous deciduous tree species and conifers - to show different results depending on the species, the direction of the grain and the effects of surface treatment of a blasted surface.The results of my tests were sometimes unexpected, such as that the sand from blasting almost completely disappeared, that all wood surfaces after blasting exhibited a much lighter or paler surface than before and that the diffuse-porous tree species showed differences in hardness between the beginning and end of annual rings.By creating a library of different kinds of wood and sandblasted surface treatment, I have created a reference bank that I will be able to use me in the manufacturing of interiors, furniture and other objects..

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

C3LOOPS is an application for DJs and VJs based on surface interaction. A system is said to be based on surface interaction if it presents content on a two dimensional, endless surface that a user navigates through zoom, pan and incremental text filtering where processing is tightly coupled with the content without breaking the workflow. C3LOOPS is designed to encourage improvisation and collaboration. During improvisation changes occur rapidly. Allowing navigation through time as well as the two spatial dimensions of an interaction surface the possibility of unlimited undo operations opens up.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.